View CLAA154WB08AN_7828547.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

c c h h u u n n g g h h w w a a p p i i c c t t u u r r e e t t u u b b e e s s , , l l t t d d . . t t e e c c h h n n i i c c a a l l s s p p e e c c i i f f i i c c a a t t i i o o n n to : date : 2007/ accepted by approved by checked by prepared by S?P ? ? prepared by : tft-lcd product planning management division chunghwa pictuer tubes, ltd. 1127 hopin rd., padeh, taoyuan, taiwan 334, r.o.c. tel: +886-3-3675151 fax: +886-3-377-3001 doc. no: claa154wb08a n issue date: 2007 cpt tft-lcd claa154wb08a n www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 2/ 22 claa154wb08a n record of revisions revision no. date page description v1 2007/08/22 final. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 3/ 22 claa154wb08a n contents no. item page 1 overview 4 2 absolute maximum ratings 5 3 electrical characteristics 6 4 connector interface pin & function 10 5 interface timing chart 11 6 block diagram 14 7 mechanical specification 15 8 optical characteristics 17 9 reliability test conditions 19 10 handling precautions for tft-lcd module 21 www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 4/ 22 claa154wb08a n 1. overview claa154wb08a n is 15.4 color (39.116cm) tft-lcd (thin film transistor liquid crystal display) module composed of lcd panel, lvds driver ics, control circuit and backlight. by applying 6 bit digital data, 1280 rgb(3) 800, 262k-color images are displayed on the 15.4 diagonal screen. general specifications are summarized in the following table item specification display area (mm) 331.2 (h) x 207.0 (v) (15.4-inch diagonal) number of pixels 1280 3(h) 800(v) pixel pitch (mm) 0.25875(h) 0.25875(v) color pixel arrangement rgb vertical stripe display mode normally white number of colors 262,144(6bits) gamut 50%(typ) optimum viewing angle 6 o clock response time (ms) 16ms surface treatment glare, 3h viewing angle (l/r/u/d) 45 45 /20 35 (typ.) brightness (cd/m^2) 220 cd/m 2 (5point)/6.5 ma (typ.) uniformity (min) 5point 80% consumption of power (w) 6.42w max module size (mm) 344.5(w) 222.5(h) 6.2(d) max module weight (g) 570 (max) surface treatement glare type (3h) the lcd products listed on this document are not suitable for use of aerospace equipment, submarine cable, and nuclear reactor control system and life support systems. if customers intend to use these lcd products for applications listed above or those not included in the "standard" list as follows, please contact our sales in advance. standard computer, office equipment, communication equipment, test and measurement equipment, machine tool, industrial robot, audio and visual equipment, other consumer products. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 5/ 22 claa154wb08a n 2. absolute maximum ratings the following are maximum value, which if exceeded, may cause faulty operation or damage to the unit. item symbol min. max. unit remark power supply voltage for lcd vcc 0 4.0 v lamp voltage vl 630 900 vrms lamp current il 2 6.5 marms *1). 2) lamp frequency fl 40 80 khz operation temperature top 0 50 *3). 4). 5). 6) storage temperature tstg -25 65 *3). 4). 5) delayed discharge time td -- 1 sec *7) note *1) product life-time relate to lamp current, please operate production follow statement at page 9 (b)back light . *2) when lamp current over the definition of absolute max, product life-time will decay rapidly or operate unusual. *3) the relative temperature and humidity range are as below sketch, 90%rh max. (ta40) Q *4) the maximum wet bulb temperature 39(ta Q 40) and without dewing. *5) if product in environment which over the definition of the relative temperature and humidity out of range too long, it will affect visual of lcd. *6) if you operate lcd in normal temperature range, the center surface of panel should be under 60. *7) delay discharge time test condition starting lamp voltage=1650vrms. (please follow statement at page 9 (b) back light before test td, lamp should operate at least 1min, and lamp current should follow typical lamp current specification. to place panel at room temp. (25 & 2) below for 24hrs, and then to measure td with the same starting lamp voltage in dark room. 0 20 40 60 - 25 20 40 60 80 5 90 50 temperature ( %c) (50,50.4) (60,27.7) (40,90) www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 6/ 22 claa154wb08a n 3. electrical characteristics (a) tft lcd tem symbol min typ max unit remark lcd power voltage vcc 3.0 3.3 3.6 v [note 1] lcd power current icc - 400 600 ma [note 2] rush crrent irush - - 2 a [note 4] input voltage vin 0 - vcc v common voltage vcm 1.125 1.25 1.375 v diffrential input voltage vid 250 350 450 mv threshold voltage (high) vth - - 100 mv logic input voltage (lvds: in+,in-) [note 3] threshold voltage (low) vtl -100 - - mv when vcm = +1.2v diffrential input voltage tolerance vid - - 35 mv common voltage tolerance vcm - - 35 mv [note 1] power sequence t110ms Q 1 sect5 Q 0.01 ms t250 ms 200 mst6 QQ 0.01 ms t350 ms 200 mst7 QQ data t1 t2 t3 3.0v 3.0v 0.3v vin=3.3v 0.3 v 0.3v t4 t5 lcd power supply logic signal t6 t7 backlight power supply vl data: rgb data, dclk, hd, vd, dena vcc-dip state (1)when 3.0 vcc2.7v R td10 ms Q (2)when vcc 2.7v vcc-dip condition should as the vcc-turn-off condition. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 7/ 22 claa154wb08a n td 2.7v 3.0v vin=3.3v [note 2] typical value is 0 ? 63 gray level.(horizontal line pattern) 800 line mode vcc= +3.3v circuit condition (typ.) vcc=3.3 v fv=60 hz fh=48.9 khz fclk=68.9 mhz circuit condition (max.) vcc=3.3 v f v =60 hz f h =48.9 khz f clk =68.9 mhz 64-gray: 0 ~ 63 gray www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 8/ 22 claa154wb08a n [note 3] lvds signal definite vid = vin+ C vin-, vcm = vcm+ Cvcm- , vid = vid+ C vid- , vid+ = vih+ Cvih- , vid- = vil+ C vil- , vcm = (vin+ +vin-)/2, vcm+ = (vih+ +vih-)/2, vcm- = (vil+ +vil-)/2, refer to inverter rated voltage [note 4] irush measure condition vin+ positive differential data clk input vin- negative differential data clk input www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 9/ 22 claa154wb08a n (b) back light (a.) electrical characteristics ta=25 item symbol min typ max unit remark lamp voltage(il=6.0ma) vl 657 730 803 vrms il=6.0ma lamp current il 5.5 6.0 6.5 marms *1) inverter frequency fi 50 -- 60 khz *2) 1460 -- vrms ta=25 lamp initial voltage vs 1650 -- vrms ta=0 (b) lamp life C time item il at 2.0 ma il at 6.0 ma il at 6.5 ma unit remark lamp life-time (lt) min. 15,000 min. 15,000 min.10,000 hr continuous operation*3) turn-on and turn-off operation -- min.100,000 -- times continuous operation *4) *1)measure method galvanometer connect to low voltage *2) frequency in this range can make the characteristics of electric and optics maintain in +/- 10% except hue. lamp frequency of inverter may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display. therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. under optimum operate frequency range (40~80 khz), will not effect panel life-time and relability . *3) definition of the lamp life time a. luminance (l) under 50% of specification starting lamp voltage b. starting lamp voltage: over130% of the initial value. ta=25 *4) for keeping good lighting situation, when design the inverter, it must be considered that the voltage large than starting lamp voltage. lcd module - + a inverter power supply www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 10/ 22 claa154wb08a n 4. connector interface pin & function (a) cn1 (interface signal) outlet connector: fi-xb30sl-hf10 (jae) link connector: fi-x30h (jae, link type) pin no. symbol function 1 vss ground 2 vin +3.3v power 3 vin +3.3v power 4 v_edid ddc 3.3v power 5 nc customer-end unused (open) 6 clk_edid ddc clock 7 data_edid ddc data 8 r0n minus signal of channel 0(lvds) 9 r0p plus signal of channel 0(lvds) 10 vss ground 11 r1n minus signal of channel 1(lvds) 12 r1p plus signal of channel 1(lvds) 13 vss ground 14 r2n minus signal of channel 2(lvds) 15 r2p plus signal of channel 2(lvds) 16 vss ground 17 rclkn minus signal of clock channel (lvds) 18 rclkp plus signal of clock channel (lvds) 19 vss ground 20 nc no connect 21 nc vcom test provided , but customer-end unused (open) 22 nc no connect 23 nc no connect 24 nc no connect 25 nc no connect 26 nc no connect 27 nc no connect 28 nc no connect 29 nc no connect 30 nc no connect (b) cn2 (backlight) backlight-side connector: bhsr-02vs-1 (jst) inverter-side connector: sm02b-bhss-1 (jst) pin no. symbol function 1 cth vblh (high) 2 ctl vbll (low) [note] vblh-vbll=vl www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 11/ 22 claa154wb08a n 5. interface timing chart (a). lvds input time sequence horizontal sequence (b) lcd input time sequence vertical sequence dclk first data 2 3 data (r, g, b) 1 1279 1280 invalid data invalid data last data t ha t hb dena t h tclk t vb dena t va invalid data line data 1 2 799 800 3 invalid data t v www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 12/ 22 claa154wb08a n (2) timing chart item synbol min typ max unit frequency f clk 65.3 71 74.7 mhz dclk period t clk 15.3 14.08 13.3 ns horizontal total time t h 1344 1424 1500 t clk horizontal active time t ha 1280 1280 1280 t clk horizontal horizontal blank time t hb 64 144 220 t clk vertical total time t v 810 816 830 t h vertical active time t va 800 800 800 t h lcd timing dena vertical vertical blank time t vb 10 16 30 t h [note] *1) data is latched during dclk falling period. *2) hd vd is negative. *3) dena (data enable) usually is positive. *4) during the whole blank period, dclk should keep input. during the vertical blank period, hd should keep input. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 13/ 22 claa154wb08a n (3) data mapping r data g data b data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 color input data ms b ls b ms b ls b ms b ls b black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 red(2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red(62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green(0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 green(2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 green(62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green green(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue(0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 blue(62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 [note] 1) gray level: color(n) n is level order; higher n means brighter level. 2) data: 1: high 0: low www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 14/ 22 claa154wb08a n 6. block diagram i/f connector cn1 ( lvds receiver embedded) asic gate drivers power supply circuit tft-lcd g1 g2 g800 source drivers power timing signal display data s 3839 s 3840 s1 s2 1 2 cn2 dc-ac inverter light control inverter circuit (out side) 1 2 ccfl back light cn2 www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 15/ 22 claa154wb08a n 7. mechanical specification 7.1 front side (tolerance is 0.5mm unless noted) [unit: mm] www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 16/ 22 claa154wb08a n 7.2 rear side (tolerance is 0.5mm unless noted) [unit: mm] www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 17/ 22 claa154wb08a n 8. optical characteristics ta=25 vdd=3.3v item symbol condition min. typ. max. unit remark contrast ratio cr q = ' 0 % 300 350 -- *1) luminance (5p) l q = ' 0 % 200 220 cd/m 2 *2) uniformity(5p) d l q = ' 0 % 80 % *2) tr q = ' 0 % 6 9 ms *4) response time tf q = ' 0 % 10 16 ms *4) image sticking tis 16 hours - 20 min *5) cross talk ct q = f 0 % 3 1 % *6) horizontal ' 40/-40 45/-45 *3) view angle vertical q cr10 # 15/-30 20/-35 *3) w x y 0.293 0.309 0.313 0.329 0.333 0.349 r x y 0.585 0.327 0.605 0.347 0.625 0.367 g x y 0.295 0.561 0.315 0.581 0.335 0.601 color temperature coordinate b x y q = ' 0 % 0.133 0.106 0.153 0.126 0.173 0.146 *2) these items are measured using bm-5a (topcon) under the dark room condition (no ambient light). measurement condition: il=6.0 # 6ma inverter sumida / iv12139/t definition of these measurement items is as follows: *1) definition of contrast ratio cr=on (white) luminance/off (black) luminance *2) definition of luminance and luminance uniformity central luminance: the white luminance is measured at the center position ( 1 ! on the screen, see fig.1 below. 5p uniformity: d l = (lmin / lmax) # 100% (1,1) (1280,800) 320 640 960 400 200 600 w h 1 2 3 5 4 1/4 h www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 18/ 22 claa154wb08a n *3) definition of view angle( ) *4) definition of response time *5) definition of image sticking continuously display the test pattern shown in the figure below for 16 hrs. at 25 . to change the picture to gray pattern (gray 32 pattern), and the previous image shall not persist during 20 min . *6) crosstalk modulation ratio: ct= $ y b -y a $ / y a 100% y a !y b measure position and definition y a means luminance at gray level 32(exclude gray level 0 pattern) y b means luminance at gray level 32(include gray level 0 pattern) luminance white black 90 % 90 % 10 % 10 % tf tr upper(+) right(+) left(-) gate drive side lcd panel lower(-) white 63 gray black 0 gray 32 www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 19/ 22 claa154wb08a n 9.reliability test conditions (1) temperature and humidity test items conditions high temperature operation 50 ? 240hrs high temperature storage 60 ? 240hrs high temperature high humidity operation 50 ? 90 rh 240hrs high temperature high humidity storage 60 ? 90 rh 48 hrs low temperature operation 0 ? 240 hrs low temperature storage -20 ? 240 hrs thermal shock -20 (0.5 hr) ? 60 (0.5 hr) ramp<20 100 cycle temperature & pressure storage 25 ? 260hpa(about 10000m) 24 hrs (2) shock & vibration test items conditions shock (non-operation) shock level : 1960m/s 2 (200g), waveform : half sinusoidal wave, 2ms, 6 axis ( x, y, z) per cycle vibration (non-operation) vibration level : 9.8m/s 2 (1.0g), sinusoidal wave (each x,y,z axis : 1hr, total 3hrs) frequency range : 5 ?500 hz sweep speed : 0.5 octave/min. (3) esd surface discharge(panel display area frame pwb panel back side) electrics capacity of connector contact air contact capacity 150 pf 150 pf 200 pf resistance 330 ? 330 ? 0 ? voltage 8kv 8kv/ 15kv 250 v interval 1 sec 1 sec 1 sec times(single point) 25 25 1 air discharge air discharge acceptance criteria +/-8 kv +/-15 kv a permitted permitted b permitted permitted c not permitted permitted d not permitted not permitted www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 20/ 22 claa154wb08a n acceptance definitions a normal operation. no degradation. no failures. b some performance degradation allowed. no data lost. self- recoverable. c temporary performance degradation. recovery by operator is acceptable. d degradation or loss of function,which is not recoverable due to damage of equipment (components) (4) judgment standard the judgment of the above test should be made as follow: pass normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail no display image, obvious non-uniformity, or line defects. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 21/ 22 claa154wb08a n 10. handling precautions for tft-lcd module please pay attention to the followings in handling- tft-lcd products; 10.1 assembly precaution (1) please use the mounting hole on the module side in installing and do not beading or wrenching lcd in assembling. and please do not drop, bend or twist lcd module in handling. (2) please design display housing in accordance with the following guidelines. housing case must be destined carefully so as not to put stresses on lcd all sides and not to wrench module. the stresses may cause non-uniformity even if there is no non-uniformity statically. keep sufficient clearance between lcd module back surface and housing when the lcd module is mounted. approximately 1.0 mm of the clearance in the design is recommended taking into account the tolerance of lcd module thickness and mounting structure height on the housing. when some parts, such as, fpc cable and ferrite plate, are installed underneath the lcd module, still sufficient clearance is required, such as 0.5mm. this clearance is, especially, to be reconsidered when the additional parts are implemented for emi countermeasure. design the inverter location and connector position carefully so as not to give stress to lamp cable, or not to interface the lcd module by the lamp cable. keep sufficient clearance between lcd module and the others parts, such as inverter and speaker so as not to interface the lcd module. approximately 1.0mm of the clearance in the design is recommended. (3) please do not push or scratch lcd panel surface with any-thing hard. and do not soil lcd panel surface by touching with bare hands. (polarizer film, surface of lcd panel is easy to be flawed.) (4) please do not press any parts on the rear side such as source tcp, gate tcp, control circuit board and fpcs during handling lcd module. if pressing rear part is unavoidable, handle the lcd module with care not to damage them. (5) please wipe out lcd panel surface with absorbent cotton or soft clothe in case of it being soiled. (6) please wipe out drops of adhesives like saliva and water on lcd panel surface immediately. they might damage to cause panel surface variation and color change. (7) please do not take a lcd module to pieces and reconstruct it. resolving and reconstructing modules may cause them not to work well. (8) please do not touch metal frames with bare hands and soiled gloves. a color change of the metal frames can happen during a long preservation of soiled lcd modules. (9) please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter. 10.2 operating precautions (1) please be sure to turn off the power supply before connecting and disconnecting signal input cable. (2) please do not change variable resistance settings in lcd module. they are adjusted to the most suitable value. if they are changed, it might happen lcd does not satisfy the characteristics specification. (3) please consider that lcd backlight takes longer time to become stable of radiation characteristics in low temperature than in room temperature. (4) a condensation might happen on the surface and inside of lcd module in case of sudden change of ambient temperature. (5) please pay attention to displaying the same pattern for very long time. image might stick on lcd. if then, time going on can make lcd work well. (6) please obey the same caution descriptions as ones that need to pay attention to ordinary electronic parts. www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
cpt chunghwa pictures tubes, ltd., cpt confidential 22/ 22 claa154wb08a n 10.3 precautions with electrostatics (1) this lcd module use cmos-ic on circuit board and tft-lcd panel, and so it is easy to be affected by electrostatics. please be careful with electrostatics by the way of your body connecting to the ground and so on. (2) please remove protection film very slowly on the surface of lcd module to prevent from electrostatics occurrence. 10.4 storage precautions (1) when you store lcds for a long time, it is recommended to keep the temperature between 0 ~40 without the exposure of sunlight and to keep the humidity less than 90%rh. (2) please do not leave the lcds in the environment of high humidity and high temperature such as 60 90%rh. (3) please do not leave the lcds in the environment of low temperature; below -20 . 10.5 safety precautions (1) when you waste lcds, it is recommended to crush damaged or unnecessary lcds into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) if any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off throughly with soap and water. 10.6 others (1) a strong incident light into lcd panel might cause display characteristics' changing inferior because of polarizer film, color filter, and other materials becoming inferior. please do not expose lcd module direct sunlight land strong uv rays. (2) please pay attention to a panel side of lcd module not to contact with other materials in preserving it alone. (3) for the packaging box, please pay attention to the followings: packaging box and inner case for lcd are designed to protect the lcds from the damage or scratching during transportation. please do not open except picking lcds up from the box. please do not pile them up more than 3 boxes. (they are not designed so.) and please do not turn over. please handle packaging box with care not to give them sudden shock and vibrations. and also please do not throw them up. packing box and inner case for lcds are made of cardboard. so please pay attention not to get them wet. (such like keeping them in high humidity or wet place can occur getting them wet.) www.yslcd.com.tw studio technology co.,ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of CLAA154WB08AN

	To Download CLAA154WB08AN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .